1. Product Dimensions and Weight Information
2. Accessory Kits
This complete kit includes the necessary components for an ideal installation, optimizing the toilet's incineration process and function.
There are three types of accessory kits:
- 1 ) Standard Vertical Hard Pipe Kit
- 2 ) Standard Vertical Flexible Hose Kit
- 3 ) Side Installation Hard Pipe Kit
(Please consult sales customer service when purchasing the product to choose the most suitable kit based on your installation environment)
1 ) Standard Vertical Hard Pipe Kit
- 304 Stainless Steel Rain Cap x 1
- Smooth Sweep Tee x 1
- Φ110MM Exhaust Pipe 1meter x 2
- 304 Stainless Steel Side Exhaust/Intake Guard x 1
- 304 Stainless Steel Clamp (Φ114-120) Adjustable 100-150MM x 2
- M4 / 12 MM Countersunk Self-tapping Screw (304Stainless Steel) x 12
2） Standard Vertical Flexible Hose Kit
- 304 Stainless Steel Rain Cap x 1
- Φ110MM Extendable Flexible Hose x 1
- 304 Stainless Steel Side Exhaust/Intake Guard x 1
- 304 Stainless Steel Clamp (Φ114-120) Adjustable 100-150MM x 1
- M4 / 12 MM Countersunk Self-tapping Screw (304 Stainless Steel) x 12
- Φ110MM Exhaust Hard Pipe 20cm
3 ) Side Installation Hard Pipe Kit
- 304 Stainless Steel Side Exhaust/Intake Guard x 2
- M4 / 12 MM Countersunk Self-tapping Screw (304 Stainless Steel) x 10
- Φ110MM Exhaust Pipe 30cm x 1
- Φ110MM Exhaust Pipe 60cm x 1
3. Installing the Exhaust Pipe
Method 1: Standard VerticInstallation al Hard Pipe Assembly Schematic
- As shown in the diagram, the gap between the back of the incineration toilet and the wall is recommended to be no less than 50MM.
- According to your installation environment, after fixing the toilet in place, cut the exhaust pipe and intake pipe to suitable lengths.
- After determining the hole spacing for the exhaust pipe, drill two holes with a diameter of 111MM in the wall.
- Install the cut exhaust pipe between the incineration toilet and the wall.
- Then, mark two evenly distributed positions on the wall along the central axis of the exhaust hole center to install two 304 stainless steel clamps.
- Fix the clamps using M4\12MM countersunk screws in the pre-drilled screw holes on
the clamps. - Place the exhaust pipe into the pre-installed clamps, then tighten the clamp locking screws to secure the exhaust pipe.
Method 2: Standard Vertical Flexible Hose Assembly Schematic
- According to your installation environment, after fixing the toilet in place, cut the intake pipe to a suitable length.
- Fix the 304 stainless steel rain cap to one end of the flexible hose using M4 countersunk self-tapping screws.
- After determining the hole spacing for the intake pipe, drill holes in the wall: exhaust hole 126MM, intake hole 111MM.
- Determine a position for assembling the 304 stainless steel clamp on the central axis of the exhaust hole center, and assemble the clamp onto the wall.
- Then, pass the exhaust hose and intake pipe through the holes respectively, fixing them between the toilet and the wall.
- Fix the rain cap onto the pre-assembled clamp, and tighten the clamp locking screw to secure the rain cap.
Method 3: Side Installation Hard Pipe Assembly Schematic
- According to your installation environment, after fixing the toilet in place, cut the exhaust pipe and intake pipe to suitable lengths.
- After determining the hole spacing for the exhaust pipe, you can drill two holes with a diameter of 111MM in the wall.
- Install the cut exhaust pipe and intake pipe between the incineration toilet and the wall bracket as shown.
- Then, use M4\12MM countersunk self-tapping screws to fix the guards on the outside of the wall for the exhaust and intake holes respectively (as shown).
3.Testing System Function and Full Machine Performance
- When the "Start" button is pressed, the incineration cycle will be activated.
- The estimated incineration time for verification testing is about 60-120 minutes.
- A complete test can only be finished if there are no fault indications or system interruptions.
- The toilet must cool down until the fan stops running before it enters standby mode.
- The cooling phase may take 60-90 minutes.
